How To Tighten Chain On Ryobi Pole Saw?
Chainsaws can prove dangerous if they are not properly handled. Before you use them, make sure that the chain is securely fastened. This guide will show you how to do just that in a few simple steps.
Simply put, the adjustment knob is located near the handle of your saw. This allows you to tighten the chain. To tighten the chain, turn it clockwise. To loosen it, turn it counterclockwise.
If you want to know more follow these steps below and youll be able to tighten the chain on your Ryobi pole saw like a pro in no time. A properly tightened chain will allow you to use your saw confidently and safely through any material.
These steps will tighten your chain.
-
Step 1
Turn the tension knob. Hold the Ryobi pole saw in one hand and the exposed shaft with the other. Twist this clockwise until you hear a click, at which point it should stop turning.
Youve now disengaged your pole saws chain brake. You should not move forward until the knob is fully loosen. Now, release the driveshaft.
-
Step 2
The bar nuts at the end are loosen from the notch. Use a flathead screwdriver or similar tool for assistance if necessary; also note that these are left-handed threads, so turn them counterclockwise to free them.
-
Step 3
The blade assembly should be pulled towards you until it stops. While holding the front handle with one hand, use your other hand to hold the blade steady while you unhook its bar nuts from their respective notches in the blade casing.
Note that the other side must also be done at this point; if not, simply rotate your device around and finish disengaging both sides of the lower bar nuts using your flathead screwdriver before moving forward. Once this is complete, set aside these items for now.
-
Step 4
Remove the lower guard by simply pulling it off the bottom of the saws frame.
-
Step 5
Use an adjustable wrench to unscrew the nut on the bottom of the saws blade assembly. Be aware that this is a reverse-threaded nut, so turn it clockwise to remove it.
-
Step 6
The blade assembly should be pulled towards you until it stops. You can remove the newly released chain from around your bar by opening your lower guard.
Then, carefully remove your chain by unhooking its retaining link in order to detach one chain segment at a time. After you have done this, take your blade assembly off of you and set these parts aside.
-
Step 7
Use an adjustable wrench to loosen the three bolts that hold the saw’s upper blade assembly together.
Note that these are regular-threaded bolts, so turn them clockwise to remove them. After this is done, lift the upper blade assembly in half and place it aside.
-
Step 8
To remove the old chain, unhook its retaining link and take it apart one segment at a while until all links are gone.
-
Step 9
The new chain should be placed around the bar. It will be easier to do this if your lower guard is open. Next, attach each link one at a while being careful to align. The goal should be about 3/20 cm.
-
Step 10
Attach the upper blade assembly to both halves, tighten it with a wrench, then replace all three bolts that were removed earlier.
Be aware that these are reverse-threaded bolts, so turn them counterclockwise to tighten them. After that, you can reattach the lower protection that was left behind.
Tips For Avoiding Future Problems With The Chain Tension:
You can take a few easy steps to make sure your chain stays taut and doesn’t slip off the bar as often.
First, don’t cut branches that are more than 3 inches in diameter. They will put too much downward pressure on your saw bar and make it unsafe to use this tool.
You should also avoid cutting through the trunk of any tree, as this will cause the same problem and could damage your saw.
You should also check the tension of your chain immediately after every cut. If it is not correct, adjust it as necessary (see step 3). This will ensure that the chain doesnt come off in the middle of a potentially dangerous cut.
Final Thoughts:
Although tightening the chain on a Ryobi polesaw is easy, it is essential to do it correctly to prevent damage to the saw or injury to the user.
FAQs
1. What are the symptoms of a loose chain on a Ryobi pole saw?
Symptoms of a loose chain on your Ryobi pole saw are similar to those caused by any other poorly-adjusted or malfunctioning power tool. You may experience increased vibration, insufficient cutting power, and – in the worst case – an outright loss of function. These symptoms could be a sign that your chainsaw blades or sharpening stones are worn.
2. How can you tell if your chain is too loose?
If the chain is too loose it can cause it to start running erratically and stop performing as well as a properly adjusted saw. You might notice a strain in your saw’s motor when it happens, such as while splitting wood. This is a sign that there is something wrong with the blade assembly.
3. The tools and materials you will need to tighten the chain?
The tools and materials needed to tighten the chain on your Ryobi pole saw are similar to those necessary for any other power tool, with a few notable exceptions. Rather than just one or two wrenches, you will likely require both an adjustable wrench and large channel locks in order to get sufficient torque on many bolts. If you find it too difficult to replace the chain, the most difficult task is removing the blade assembly.
